The print process for Fuse 1 generation printers requires that the material be sintered at a precise temperature, which is measured by the printer’s IR sensor. While most printers maintain this temperature without the need for adjustment, some print defects and issues can be addressed by fine-tuning the print bed temperature.

Formlabs recommends tuning the bed temperature of your printer before printing with Nylon 12 Powder for the first time. Fine-tuning the bed temperature prior to printing your first build results in fewer surface defects on your parts caused by variable printer temperatures. This process is run as a diagnostic print, uploaded through PreForm to the printer. The print contains several parts that need to be cleaned and inspected to determine the necessary temperature offset for your printer. This process should be run on aged powder, refreshed with 30% fresh powder. If you do not have any used powder on hand, age a batch of fresh powder before printing the bed temperature tuning diagnostic tool.

1. If you have previously used the printer with an applied offset, reset the printer’s offset to 0 prior to beginning the fine-tuning process. This can be done by following the directions to Set the Bed Temperature Target, and setting the printer offset to 0.
2. Update PreForm to the latest version.
3. Download the appropriate FLZ file for your printer from the links below.
• Fuse 1
• Fuse 1+ 30W (firmware version 1.22.0 or later)
• Fuse 1+ 30W (firmware version 1.21.1 or earlier)
4. Open PreForm and select Job Settings.
5. In the Job Setup window, make sure the correct printer is selected.
6. Select Upload Diagnostic Print.

7. Upload the file from your computer and start the print.
8. Load the hopper with 3 kg of powder. Fill the hopper to the 7 L mark.
9. Allow the print to fully cool per Formlabs recommendations.

Extract parts using the Fuse Sift or the Fuse Depowdering Kit. Excess powder can be sifted with fresh powder and re-used.

Clean parts prior to inspection either using the Fuse Blast or other media blasting solutions. Extract the five plaques with cones. The additional flat plaques in the build create equal cooling and separation between the cone plaques during the print and can be discarded.

Each plaque lists the temperature offset it was printed with (-2 ºC, -1 ºC, 0 ºC, +1 ºC, +2 ºC). Line the plaques up from -2 ºC to +2 ºC to prepare them for inspection.

To determine the appropriate temperature offset for your printer, look for two things:

• More than one instance but less than six instances of orange peel on a single plaque. This is most visible on the cones.
• No pitting. This is most visible on the side of the plaque opposite the cones.

Rotate the plaques to inspect the cones from all angles. Orange peel appears as a slightly layered surface on the cones. Pitting appears as a tiny dot on the opposite side of the plaques.

After inspecting all five plaques, determine the offset temperature that best matches the above criteria using the temperature offsets listed on the plaques. This offset can then be manually set on the machine.

可按 0.25°C 的增量将打印床目标温度调节 ±5°C。后 完成打印床温度调试打印后，调整打印机上的打印床目标温度，使其与 在打印床温度调试检查期间确定的偏移量。

调整打印床目标温度：

1. 确保打印机未运行打印任务，且当前处于空闲状态。打印床 Temperature Target（目标温度）只能在打印前进行调整，打印运行时无法调整。
2. 点击打印机触摸屏上的齿轮图标。随即显示 Settings（设置）界面。
3. 点击 Calibration（校准）。随即显示 Calibration（校准）界面。
4. 点击Bed Temperature Target（打印床目标温度）。随即显示有关目标温度信息的界面。
5. 点击 Next（下一步）。随即显示 Bed Temperature Target（打印床目标温度）界面。

6. 点击 + 或 - ，增加或减少温度 偏移。
7. 完成调整温度偏移后，点击下一步。确认 新的偏移量，然后点击 Set（设置）。