注意：
请务必参阅溶剂供应商提供的安全数据表 (SDS)，并将其作为储存和处理溶剂的主要信息来源。
Form Studio Wash+Cure time settings
Form Studio Wash+Cure time settings
The Form Studio Wash+Cure removes uncured resin from the surface of printed parts by simultaneously soaking and moving them in a solvent. The machine can be used with Formlabs Resin Washing Solution, isopropyl alcohol (IPA), or tripropylene glycol monomethyl ether (TPM).
After your parts are washed and dried, swap the wash bucket for the turntable and switch the machine to cure mode. Place the printed parts on the turntable and post-cure them so the resin achieves its optimal mechanical properties.
The table below indicates the recommended times to wash and post-cure parts printed in Formlabs resins using the Form Studio Wash+Cure. Formlabs updates wash settings periodically with new and improved materials. Check for updated wash settings when using a new resin or revised formulation.
Note:
When using TPM, wash your printed parts as you would with IPA. Use longer wash times if necessary—some resins will not absorb TPM or swell as much with exposure to the solvent. Refer to the support article Washing prints with TPM for more information about the TPM wash process and the effect of TPM on resins.
| Resin | Wash time | Post-cure time |
|---|---|---|
| Alpha Black Resin V1 | 5 minutes (or until clean) | 5 minutes |
| Alpha Clear Resin V1 | 5 minutes (or until clean) | 5 minutes |
| Alpha Fast Resin V1 | 5 minutes (or until clean) | 5 minutes |
| Alpha Grey Resin V1 | 5 minutes (or until clean) | 5 minutes |
| Alpha Model Resin V1 | 5 minutes (or until clean) | 5 minutes |
| Alpha White Resin V1 | 5 minutes (or until clean) | 5 minutes |
| Flexible 80A Resin V2 |
5 minutes + 5 minutes (or until clean) Wash parts printed in Flexible 80A Resin V2 in two cycles, preferably using fresh solvent for the second wash. |
Step 1 (optional): Place dry parts in a glass beaker (or other UV-transparent container) and completely submerge the parts in room temperature water. Cure for 5 minutes. Step 2: Remove parts from water. Cure for 30 minutes. |
| Tough 1500 Resin V2 (Form Studio 1) |
10 minutes (or until clean)
|
25 minutes |
| True Cast Resin V1 |
5 minutes Dry with compressed air, rinse with fresh solvent, then dry with compressed again. |
3 minutes |
更改建议清洗时间
在以下情况下，可能需要延长推荐的清洗时间：
- 清洗中空、凹陷、大型或长型部件和内部通道。 使用 Finish Kit 手动循环清洗桶中的溶剂
- 。
- 在高浓度树脂的溶剂中清洗部件。
提示：
请遵循这些清洗打印件的最佳做法，以获得最洁净的部件。
回收或处置废溶剂
有关安全处置废溶剂的更多信息，请参阅支持文档 异丙醇 (IPA)、Formlabs Resin Washing Solution 和 三丙二醇单甲醚 (TPM)。
注意：
请勿将液态或者半固化树脂倒入下水道或者与生活垃圾一起处置。请勿将含有溶解树脂的溶剂倒入下水道或者与家庭垃圾一起处置。废溶液安全而适当的处置方法因地区而异。